Adjustments|Adjustment Items

Quality Adjustment

Adjustment item and description		Objects/range of adjustment
01 Package Color Auto Adj. This menu item is to be displayed on the machine mounted with Integrated Color Care Unit IQ-501.
	Automatically adjust colors collectively.	-
02 Package Color Manual Adj. Manually adjust color adjustment items collectively.		-
03 Density Balance Auto. Adj. Perform the density balance adjustment using the scan function.		-
04 Maximum Density Adjustment
	Adjust the maximum density. The machine will start the Gamma Automatic Adjustment after you change the maximum density. Be sure to perform Color Density Manual Control after changing the maximum density.	(Light)-10, -9, -8, -7, -6, -5, -4, -3, -2, -1, 0, +1, +2, +3, +4, +5* (Dark) * The maximum density can be changed. To change this setting, contact your service representative.
05 Max. Density Auto Adj. When Relay Unit RU-518 is mounted on the machine without Integrated Color Care Unit IQ-501, Max. Density Auto Adj. (RU) is displayed. If either optional unit is not mounted on the machine, this function is not displayed.
	Chart printing and scanning are performed automatically, and the maximum density is adjusted automatically. Be sure to perform Color Density Manual Control after changing the maximum density.	-
06 Color Density Control
	Make settings for controlling the color density of output paper.	-
07 Periodical Both Sides Adj. This menu item is to be displayed on the machine mounted with Integrated Color Care Unit IQ-501.
	Configure settings for the periodical both-side adjustment.	Period. Both Sides Auto Adj.: ON, OFF Adjustment Interval (100 to 9,999 sheets) Deviation Check: ON, OFF Specified Value (0.5 to 10.0 mm)

Machine Adjustment

Adjustment item and description	Objects/range of adjustment
01 Printer Adjustment
	01 Restart Timing Adjustment Adjust the image position of lead edge in paper feed direction in the printer engine. Prerequisite: FD-Mag. Adjustment is completed.	Objects of adjustment: Side1: All Trays Offset Adj. Range: -45~+45 1 step = 0.1 mm Objects of adjustment: Side1, Side2 Restart Timing(Tray1), Restart Timing(Tray2), Restart Timing(Tray3), Restart Timing(Tray4), Restart Timing(Tray5), Restart Timing(Tray6), Restart Timing(Tray7), Restart Timing(Tray8), Restart Timing(Tray9), Restart Timing(Tray10), Restart Timing(Tray11) Adj. Range: -30~+30 1 step = 0.1 mm [-] Lower [+] Higher
	02 Centering Adjustment Adjust the image position in the crosswise direction of the printer engine. Prerequisite: CD-Mag. Adjustment is completed.	Mis-center Detect Setting: ON, OFF Adj. Range: -64~+63 1 step = 0.1 mm [-] Front [+] Back
	03 FD-Mag. Adjustment Adjust the magnification in paper feed direction in the printer engine.	Objects of adjustment: Side1 Printer FD-Mag. Adj. Range: -10~+10 1 step = 0.05% Objects of adjustment: Side2 Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11 Adj. Range: -10~+0 1 step = 0.05% [-] Short [+] Long
	04 CD-Mag. Adjustment Adjust the magnification in crosswise direction in the printer engine.	Objects of adjustment: Side1 Printer CD-Mag. Adj. Range: -10~+10 1 step = 0.05% Objects of Adjustment: Side2 Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11 Adj. Range: -10~+0 1 step = 0.05% [-] Short [+] Long
02 Scan Adjustment
	01 Restart Timing Adjustment Adjust the scan starting position when scanning the original on the original glass. Prerequisite: FD-Mag. Adjustment is completed.	Adj. Range: -30~+30 1 step = 0.1 mm [-] Image Slow [+] Image Fast
	02 Centering Adjustment Adjust the image position in the crosswise direction when scanning the original on the original glass. Prerequisite: Printer Centering Adjustment is completed.	Objects of adjustment: Orig. Glass Centering Adj. Range: -57~+57 1 step = 0.1 mm [-] Back [+] Front
	03 FD-Mag. Adjustment Adjust the magnification in feed direction when scanning the original on the original glass. Prerequisite: Printer FD-Mag. Adjustment is completed.	Adj. Range: 990~1010 1 step = 0.001 [-] Short [+] Long
	04 CD-Mag. Adjustment Adjust the magnification in the crosswise direction when scanning the original from the original glass. Prerequisite: Printer CD-Mag. Adjustment is completed.	Adj. Range: 990~1010 1 step = 0.001 [-] Short [+] Long
03 LPH Adjustment
	01 Gap Adj. Between LPH Chips Adjust the gap (39 points) between LPH chips.	Object of adjustment (Chip) 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28 , 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39 Adj. Range: -8~+8 1 step = 1.0 % Select Test Pattern: Dark Gray, Light Gray Line Draw: ON, OFF All Offset: Collectively adjusts all chips. [-] Lighter [+] Darker

Adjustment item and description

Objects/range of adjustment

01 Printer Adjustment

01 Restart Timing Adjustment

Adjust the image position of lead edge in paper feed direction in the printer engine.

Prerequisite: FD-Mag. Adjustment is completed.

Objects of adjustment:

Side1: All Trays Offset

Adj. Range: -45~+45 1 step = 0.1 mm

Objects of adjustment: Side1, Side2

Restart Timing(Tray1), Restart Timing(Tray2), Restart Timing(Tray3), Restart Timing(Tray4), Restart Timing(Tray5), Restart Timing(Tray6), Restart Timing(Tray7), Restart Timing(Tray8), Restart Timing(Tray9), Restart Timing(Tray10), Restart Timing(Tray11)

Adj. Range: -30~+30 1 step = 0.1 mm

[-] Lower [+] Higher

02 Centering Adjustment

Adjust the image position in the crosswise direction of the printer engine.

Prerequisite: CD-Mag. Adjustment is completed.

Mis-center Detect Setting: ON, OFF

Adj. Range: -64~+63 1 step = 0.1 mm

[-] Front [+] Back

03 FD-Mag. Adjustment

Adjust the magnification in paper feed direction in the printer engine.

Objects of adjustment: Side1

Printer FD-Mag.

Adj. Range: -10~+10 1 step = 0.05%

Objects of adjustment: Side2

Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11

Adj. Range: -10~+0 1 step = 0.05%

[-] Short [+] Long

04 CD-Mag. Adjustment

Adjust the magnification in crosswise direction in the printer engine.

Objects of adjustment: Side1

Printer CD-Mag.

Adj. Range: -10~+10 1 step = 0.05%

Objects of Adjustment: Side2

Tray1, Tray2, Tray3, Tray4, Tray5, Tray6, Tray7, Tray8, Tray9, Tray10, Tray11

Adj. Range: -10~+0 1 step = 0.05%

[-] Short [+] Long

02 Scan Adjustment

01 Restart Timing Adjustment

Adjust the scan starting position when scanning the original on the original glass.

Prerequisite: FD-Mag. Adjustment is completed.

Adj. Range: -30~+30 1 step = 0.1 mm

[-] Image Slow [+] Image Fast

02 Centering Adjustment

Adjust the image position in the crosswise direction when scanning the original on the original glass.

Prerequisite: Printer Centering Adjustment is completed.

Objects of adjustment:

Orig. Glass Centering

Adj. Range: -57~+57 1 step = 0.1 mm

[-] Back [+] Front

03 FD-Mag. Adjustment

Adjust the magnification in feed direction when scanning the original on the original glass.

Prerequisite: Printer FD-Mag. Adjustment is completed.

Adj. Range: 990~1010 1 step = 0.001

[-] Short [+] Long

04 CD-Mag. Adjustment

Adjust the magnification in the crosswise direction when scanning the original from the original glass.

Prerequisite: Printer CD-Mag. Adjustment is completed.

Adj. Range: 990~1010 1 step = 0.001

[-] Short [+] Long

03 LPH Adjustment

01 Gap Adj. Between LPH Chips

Adjust the gap (39 points) between LPH chips.

Object of adjustment (Chip) 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28
, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39

Adj. Range: -8~+8 1 step = 1.0 %

Select Test Pattern: Dark Gray, Light Gray

Line Draw: ON, OFF

All Offset: Collectively adjusts all chips.

[-] Lighter [+] Darker

Finisher Adjustment (Finisher FS-532)

This menu item is displayed and can be set on the machine mounted with Finisher FS-532.

Adjustment item and description	Objects/range of adjustment
01 Staple Finisher Adjustment 01 Staple Finisher(Main) Adj.
	01 Exit Guide Paper Width Adj. Adjust the exit guide alignment pitch to be used by the staple finisher. Make adjustment if output paper stack on main tray is uneven in straight delivery.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 13 19 short edge feed, B5 short edge feed, Postcard, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] Wide [+] Narrow
	02 Upper Gripper Operation Select the upper gripper operation for main tray delivery exit.	Auto, ON, OFF
	03 Output Alignment Operation Select operation for output alignment.	Auto, ON, OFF
	04 Staple Paper Width Adj. Adjust the board alignment width of the staples in the staple finisher.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm) Adj. Range: -20~+20 1 step = 0.1 mm [-] Wide [+] Narrow
	05 FD Alignment Plate Adj. Adjust the vertical alignment fitting for staples in the staple finisher.	Objects of adjustment: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, 9 11 long edge feed, 5.5 8.5 long edge feed, Custom(139~230 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] Wide [+] Narrow
	06 Staple Position Adjustment Adjust 2 position staple pitch and corner staple positions in the staple finisher.	Objects of adjustment: 2 Position Pitch (120 mm), 2 Position Pitch (140 mm), 2 Position Pitch (165 mm), Rear Diagonal Adj. Range: -5~+5 1 step = 1 mm Objects of adjustment: Rear Parallel, Front Parallel Adj. Range: -3~+3 1 step = 1 mm [-] Narrow [+] Wide
	07 Rewind Paddle Descent Adj. Adjust rewind paddle descent.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm) Adj. Range: -10~+10 1 step = 0.2 mm [-] Little [+] Much
	08 Rewind Function Operation Select operation for the rewind paddle.	Auto, ON, OFF
02 Staple Finisher(Fold) Adj. This menu item is to be displayed and become configurable on Finisher FS-532 mounted with Saddle Stitcher SD-510.
	01 Fold&Staple Paper Width Adj. Adjust pitch of alignment plate in Saddle Stitcher SD-510 if half-folded or multi tri-folded paper show misalignment in the crosswise direction to paper feeding.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] Narrow [+] Wide
	02 Fold&Staple Pitch Adjustment Adjust staple pitch in Saddle Stitcher SD-510. Make this adjustment if staple pitch is not within the allowance range.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm) Adj. Range: -300~+300 1 step = 0.1 mm Staple pitch: [-] Narrow [+] Wide
	03 Fold&Staple Fold Position Adjust half-fold position of fold & staple function in Saddle Stitcher SD-510. Make this adjustment if half-fold position is not within the specified range.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm) Adj. Range: -50~+50 1 step = 0.1 mm Upper output side: [-] Extend [+] Shorten
	04 Fold&Staple Staple Position Adjust staple position in Saddle Stitcher SD-510.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm) Adj. Range: -50~+50 1 step = 0.1 mm Upper output side: [-] Extend [+] Shorten
	05 Half-Fold Fold Position Adj. Adjust half-fold position of fold function in Saddle Stitcher SD-510.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm) Adj. Range: -50~+50 1 step = 0.1 mm Upper output side: [-] Extend [+] Shorten
	06 Tri-Fold Adjustment
		01 Tri-Fold Position Adjustment Adjust Fold 1 and Fold 2 positions for multi tri-folding in Saddle Stitcher SD-510. Make this adjustment if each fold position for tri-folding is not within the allowance range.	Objects of adjustment: 8.5 11 short edge feed, A4 short edge feed, 16K short edge feed Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm Fold 1: [-] Extend [+] Shorten Fold 2: [-] Shorten [+] Extend
		02 Double Fold Plate Adjustment Adjust double fold plate in saddle stitcher. Make the insertion deeper if the Fold 2 misalignment is large.	Objects of adjustment: 8.5 11 short edge feed, A4 short edge feed, 16K short edge feed Adj. Range: -50~+50 1 step = 0.1 mm Quantity of inserting double fold plate: [-] Shallow [+] Deep
	07 Half-Fold Strength Adj. To suppress the opening of booklets, increase the roller pressure time. - You cannot adjust the strength to fold booklets. - Long pressure time causes less productivity.	Adj. Range: 0~+10 1 step = 1 sec.
03 Staple Finisher(Punch) Adj. This menu item is to be displayed and configurable on Finisher FS-532 mounted with Punch Kit PK-522.
	01 Registration Adjustment If the punch position is not parallel to the paper edge, control the paper curl and wrinkle by adjusting the paper loop amount of the registration roller.	Adj. Range: -50~+50 1 step = 0.1 mm [-] Short [+] Long
	02 Horizontal Position Adj.(FD) Adjust the distance between the edge of the printed paper and the center of punch holes.	Objects of adjustment: Offset for All Size, A3 short edge feed, A4 long edge feed, A4 short edge feed, SRA4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 8.5 14 short edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 9 11 long edge feed, B5 short edge feed Adj. Range: -50~+50 1 step = 0.1 mm Punch position at paper edge: [-] Far [+] Close
	03 Vertical Position Adj.(CD) Adjust the misalignment in center positions of paper and punch holes for each paper size.	Objects of adjustment: Offset for All Size, A3 short edge feed, A4 long edge feed, A4 short edge feed, SRA4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 8.5 14 short edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 9 11 long edge feed, B5 short edge feed Adj. Range: -50~+50 1 step = 0.1 mm Punch position: [-] Forward [+] Backward
04 Staple Finisher(PI) Adj. This menu item is to be displayed and configurable on Finisher FS-532 mounted with Post Inserter PI-502.
	01 PI Registration Adjustment When paper fed from the upper or lower tray of Post Inserter PI-502 has skew or wrinkle, or causes paper jam, adjust the paper loop of the registration roller.	Objects of adjustment: PI Upper Tray, PI Lower Tray Adj. Range: -5~+5 1 step = 1 mm [-] Short [+] Long

Adjustment item and description

Objects/range of adjustment

01 Staple Finisher Adjustment

01 Staple Finisher(Main) Adj.

01 Exit Guide Paper Width Adj.

Adjust the exit guide alignment pitch to be used by the staple finisher.

Make adjustment if output paper stack on main tray is uneven in straight delivery.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 13 19 short edge feed, B5 short edge feed, Postcard, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] Wide [+] Narrow

02 Upper Gripper Operation

Select the upper gripper operation for main tray delivery exit.

Auto, ON, OFF

03 Output Alignment Operation

Select operation for output alignment.

Auto, ON, OFF

04 Staple Paper Width Adj.

Adjust the board alignment width of the staples in the staple finisher.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] Wide [+] Narrow

05 FD Alignment Plate Adj.

Adjust the vertical alignment fitting for staples in the staple finisher.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, 9 11 long edge feed, 5.5 8.5 long edge feed, Custom(139~230 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] Wide [+] Narrow

06 Staple Position Adjustment

Adjust 2 position staple pitch and corner staple positions in the staple finisher.

Objects of adjustment:

2 Position Pitch (120 mm), 2 Position Pitch (140 mm), 2 Position Pitch (165 mm), Rear Diagonal

Adj. Range: -5~+5 1 step = 1 mm

Objects of adjustment:

Rear Parallel, Front Parallel

Adj. Range: -3~+3 1 step = 1 mm

[-] Narrow [+] Wide

07 Rewind Paddle Descent Adj.

Adjust rewind paddle descent.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm)

Adj. Range: -10~+10 1 step = 0.2 mm

[-] Little [+] Much

08 Rewind Function Operation

Select operation for the rewind paddle.

Auto, ON, OFF

02 Staple Finisher(Fold) Adj.

This menu item is to be displayed and become configurable on Finisher FS-532 mounted with Saddle Stitcher SD-510.

01 Fold&Staple Paper Width Adj.

Adjust pitch of alignment plate in Saddle Stitcher SD-510 if half-folded or multi tri-folded paper show misalignment in the crosswise direction to paper feeding.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] Narrow [+] Wide

02 Fold&Staple Pitch Adjustment

Adjust staple pitch in Saddle Stitcher SD-510. Make this adjustment if staple pitch is not within the allowance range.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -300~+300 1 step = 0.1 mm

Staple pitch: [-] Narrow [+] Wide

03 Fold&Staple Fold Position

Adjust half-fold position of fold & staple function in Saddle Stitcher SD-510. Make this adjustment if half-fold position is not within the specified range.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

Upper output side: [-] Extend [+] Shorten

04 Fold&Staple Staple Position

Adjust staple position in Saddle Stitcher SD-510.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

Upper output side: [-] Extend [+] Shorten

05 Half-Fold Fold Position Adj.

Adjust half-fold position of fold function in Saddle Stitcher SD-510.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, 12 18 short edge feed, A3 short edge feed, 11 17 short edge feed, 8K short edge feed, B4 short edge feed, SRA4 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, B5 short edge feed, A4 short edge feed, 16K short edge feed, 8 13 short edge feed, Custom(380~488 mm), Custom(240~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

Upper output side: [-] Extend [+] Shorten

06 Tri-Fold Adjustment

01 Tri-Fold Position Adjustment

Adjust Fold 1 and Fold 2 positions for multi tri-folding in Saddle Stitcher SD-510.

Make this adjustment if each fold position for tri-folding is not within the allowance range.

Objects of adjustment:

8.5 11 short edge feed, A4 short edge feed, 16K short edge feed

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: [-] Extend [+] Shorten

Fold 2: [-] Shorten [+] Extend

02 Double Fold Plate Adjustment

Adjust double fold plate in saddle stitcher.

Make the insertion deeper if the Fold 2 misalignment is large.

Objects of adjustment:

8.5 11 short edge feed, A4 short edge feed, 16K short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

Quantity of inserting double fold plate: [-] Shallow [+] Deep

07 Half-Fold Strength Adj.

To suppress the opening of booklets, increase the roller pressure time.

- You cannot adjust the strength to fold booklets.

- Long pressure time causes less productivity.

Adj. Range: 0~+10 1 step = 1 sec.

03 Staple Finisher(Punch) Adj.

This menu item is to be displayed and configurable on Finisher FS-532 mounted with Punch Kit PK-522.

01 Registration Adjustment

If the punch position is not parallel to the paper edge, control the paper curl and wrinkle by adjusting the paper loop amount of the registration roller.

Adj. Range: -50~+50 1 step = 0.1 mm

[-] Short [+] Long

02 Horizontal Position Adj.(FD)

Adjust the distance between the edge of the printed paper and the center of punch holes.

Objects of adjustment:

Offset for All Size, A3 short edge feed, A4 long edge feed, A4 short edge feed, SRA4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 8.5 14 short edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 9 11 long edge feed, B5 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

Punch position at paper edge: [-] Far [+] Close

03 Vertical Position Adj.(CD)

Adjust the misalignment in center positions of paper and punch holes for each paper size.

Objects of adjustment:

Offset for All Size, A3 short edge feed, A4 long edge feed, A4 short edge feed, SRA4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 8.5 14 short edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8 13 short edge feed, 5.5 8.5 long edge feed, 9 11 long edge feed, B5 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

Punch position: [-] Forward [+] Backward

04 Staple Finisher(PI) Adj.

This menu item is to be displayed and configurable on Finisher FS-532 mounted with Post Inserter PI-502.

01 PI Registration Adjustment

When paper fed from the upper or lower tray of Post Inserter PI-502 has skew or wrinkle, or causes paper jam, adjust the paper loop of the registration roller.

Objects of adjustment:

PI Upper Tray, PI Lower Tray

Adj. Range: -5~+5 1 step = 1 mm

[-] Short [+] Long

Finisher Adjustment (Output Tray OT-510)

This menu item is displayed and can be set on the machine mounted with Output Tray OT-510.

Adjustment item and description		Objects/range of adjustment
01 Staple Finisher Adjustment 01 Staple Finisher(Main) Adj.
	01 Exit Guide Paper Width Adj. Adjust the exit guide alignment pitch to be used by the staple finisher. Make adjustment if output paper stack on main tray is uneven in straight delivery.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, SRA4 short edge feed, A4 long edge feed, A4 short edge feed, A5 long edge feed, B4 short edge feed, B5 long edge feed, 8K short edge feed, 16K long edge feed, 12 18 short edge feed, 11 17 short edge feed, 9 11 long edge feed, 8.5 11 long edge feed, 8.5 11 short edge feed, 8.5 14 short edge feed, 8 13 short edge feed, B5 short edge feed, Postcard, 5.5 8.5 long edge feed, 16K short edge feed, Custom(380~488 mm), Custom(220~379 mm), Custom(139~219 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] Wide [+] Narrow
	02 Upper Gripper Operation Select the upper gripper operation for main tray delivery exit.	Auto, ON, OFF
	03 Output Alignment Operation Select operation for output alignment.	Auto, ON, OFF

Finisher Adjustment (Folding Unit FD-503)

This menu item is to be displayed and allowed on the machine mounted with Folding Unit FD-503.

Adjustment item and description	Objects/range of adjustment
02 Multi Folder Adjustment 01 Multi Folder(Punch) Adj.
	01 Paper Width Adjustment Adjust the misalignment of punch hole positions.	Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, A4 long edge feed, A5 short edge feed, B5 long edge feed, A5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 9 11 long edge feed, 5.5 8.5 long edge feed Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the randomness [+] To reduce the tilts
	02 Punch Vertical Position Adj.
		01 2-Hole Punch Adjust the vertical position of punch holes made by the folding unit.	Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, A4 long edge feed, A5 short edge feed, B5 long edge feed, A5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 9 11 long edge feed, 5.5 8.5 long edge feed Adj. Range: -40~+40 1 step = 0.1 mm [-] To move to the center [+] To move to the edge
02 3-Hole Punch Adjust the vertical position of punch holes made by the folding unit.	Adjustment range: Offset for All Size, A3 short edge feed, B4 short edge feed, A4 long edge feed, B5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 11 long edge feed, 8K short edge feed, 16K long edge feed, 9 11 long edge feed Adj. Range: -40~+40 1 step = 0.1 mm [-] To move to the center [+] To move to the edge
03 4-Hole Punch Adjust the vertical position of punch holes made by the folding unit.	Adjustment range: Offset for All Size, A3 short edge feed, B4 short edge feed, A4 long edge feed, B5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 11 long edge feed, 8K short edge feed, 16K long edge feed, 9 11 long edge feed Adj. Range: -40~+40 1 step = 0.1 mm [-] To move to the center [+] To move to the edge
02 Multi Folder(Fold) Adj.
	01 Half-Fold Position Adj. Adjust the folded position for half-fold.	Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] To shorten the top face [+] To lengthen the top face
	02 Z-Fold Position Adj. Adjust the fold positions for Z-folding. Adjust Fold 1to and Fold 2 in this order.	Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279 ~379 mm) Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm Fold 1: To narrow [-] <-> [+] To widen Fold 2: To narrow [-] <-> [+] To widen
	03 Tri-Fold-in Pos. Adj. Adjust the fold positions for tri-fold-in. Adjust Fold 1to and Fold 2 in this order.	Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm) Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm Fold 1: To narrow [-] <-> [+] To widen Fold 2: To narrow [-] <-> [+] To widen
	04 Tri-Fold-out Pos. Adj. Adjust the fold positions for tri-fold-out. Adjust Fold 1to and Fold 2 in this order.	Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm) Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm Fold 1: To widen [-] <-> [+] To narrow Fold 2: To narrow [-] <-> [+] To widen
	05 Double Parallel Pos. Adj. Adjust the fold positions for double parallel folding. Adjust Fold 1to and Fold 2 in this order.	Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm) Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm Fold 1: To narrow [-] <-> [+] To widen Fold 2: To narrow [-] <-> [+] To widen
	06 Gate Position Adj. Adjust the gate position. Adjust in order from Fold 1.	Objects of adjustment: Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm) Fold 1, Fold 2, Fold 3: Adj. Range: -50~+50 1 step = 0.1 mm Fold 1: To narrow [-] <-> [+] To widen Fold 2: To widen [-] <-> [+] To narrow Fold 3: To narrow [-] <-> [+] To widen

Adjustment item and description

Objects/range of adjustment

02 Multi Folder Adjustment

01 Multi Folder(Punch) Adj.

01 Paper Width Adjustment

Adjust the misalignment of punch hole positions.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, A4 long edge feed, A5 short edge feed, B5 long edge feed, A5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 9 11 long edge feed, 5.5 8.5 long edge feed

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the randomness [+] To reduce the tilts

02 Punch Vertical Position Adj.

01 2-Hole Punch

Adjust the vertical position of punch holes made by the folding unit.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, A4 long edge feed, A5 short edge feed, B5 long edge feed, A5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 9 11 long edge feed, 5.5 8.5 long edge feed

Adj. Range: -40~+40 1 step = 0.1 mm

[-] To move to the center [+] To move to the edge

02 3-Hole Punch

Adjust the vertical position of punch holes made by the folding unit.

Adjustment range:

Offset for All Size, A3 short edge feed, B4 short edge feed, A4 long edge feed, B5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 11 long edge feed, 8K short edge feed, 16K long edge feed, 9 11 long edge feed

Adj. Range: -40~+40 1 step = 0.1 mm

[-] To move to the center [+] To move to the edge

03 4-Hole Punch

Adjust the vertical position of punch holes made by the folding unit.

Adjustment range:

Offset for All Size, A3 short edge feed, B4 short edge feed, A4 long edge feed, B5 long edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 11 long edge feed, 8K short edge feed, 16K long edge feed, 9 11 long edge feed

Adj. Range: -40~+40 1 step = 0.1 mm

[-] To move to the center [+] To move to the edge

02 Multi Folder(Fold) Adj.

01 Half-Fold Position Adj.

Adjust the folded position for half-fold.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To shorten the top face [+] To lengthen the top face

02 Z-Fold Position Adj.

Adjust the fold positions for Z-folding.

Adjust Fold 1to and Fold 2 in this order.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279 ~379 mm)

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To narrow [-] <-> [+] To widen

Fold 2: To narrow [-] <-> [+] To widen

03 Tri-Fold-in Pos. Adj.

Adjust the fold positions for tri-fold-in.

Adjust Fold 1to and Fold 2 in this order.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm)

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To narrow [-] <-> [+] To widen

Fold 2: To narrow [-] <-> [+] To widen

04 Tri-Fold-out Pos. Adj.

Adjust the fold positions for tri-fold-out.

Adjust Fold 1to and Fold 2 in this order.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm)

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To widen [-] <-> [+] To narrow

Fold 2: To narrow [-] <-> [+] To widen

05 Double Parallel Pos. Adj.

Adjust the fold positions for double parallel folding.

Adjust Fold 1to and Fold 2 in this order.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm)

Fold 1, Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To narrow [-] <-> [+] To widen

Fold 2: To narrow [-] <-> [+] To widen

06 Gate Position Adj.

Adjust the gate position.

Adjust in order from Fold 1.

Objects of adjustment:

Offset for All Size, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8K short edge feed, Custom(380~458 mm), Custom(279~379 mm)

Fold 1, Fold 2, Fold 3: Adj. Range: -50~+50 1 step = 0.1 mm

Fold 1: To narrow [-] <-> [+] To widen

Fold 2: To widen [-] <-> [+] To narrow

Fold 3: To narrow [-] <-> [+] To widen

Finisher Adjustment (Large Capacity Stacker LS-506)

This menu item is to be displayed and allowed on the machine mounted with Large Capacity Stacker LS-506.

Adjustment item and description	Objects/range of adjustment
03 Stacker Adjustment
	01 Paper Width Adjustment Adjust the position of adjustment plates if output sheets show misalignment in crosswise direction on the stacker tray.	Adjustment range: Stacker No.1, Stacker No.2, Stacker No.3 Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the dispersion [+] To reduce the distortion
	02 Paper Length Adjustment Adjust the position of the stopper if output sheets show misalignment in paper feed direction on the stacker tray.	Objects of adjustment: Stacker No.1, Stacker No.2, Stacker No.3 Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the dispersion [+] To reduce the distortion

Adjustment item and description

Objects/range of adjustment

03 Stacker Adjustment

01 Paper Width Adjustment

Adjust the position of adjustment plates if output sheets show misalignment in crosswise direction on the stacker tray.

Adjustment range:

Stacker No.1, Stacker No.2, Stacker No.3

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the distortion

02 Paper Length Adjustment

Adjust the position of the stopper if output sheets show misalignment in paper feed direction on the stacker tray.

Objects of adjustment:

Stacker No.1, Stacker No.2, Stacker No.3

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the distortion

Finisher Adjustment (Saddle Stitcher SD-506)

This menu item is to be displayed and allowed on the machine mounted with Saddle Stitcher SD-506.

Adjustment item and description	Objects/range of adjustment
04 Saddle Stitcher Adjustment
	01 Fold Paper Width Adj. Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] To reduce the misalignment [+] To reduce the distortion
	02 Half-Fold Position Adj. Adjust the fold position determined by the half-folder.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] To shorten the top face [+] To lengthen the top face
	03 Staple Paper Width Adj. Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm) Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the dispersion [+] To reduce the distortion
	04 Staple Center Position Adjust the center position of staples determined by the saddle stitcher. Prerequisite: Staple paper width adjustment is completed.	Adj. Range: -20~+20 1 step = 0.1 mm [-] To move closer to paper center (fold) [+] To move away from paper center (fold)
	05 Staple Pitch Adjustment Adjust the staple pitch determined by the saddle stitcher.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm) Adj. Range: -20~+20 1 step = 1.0 mm [-] To shorten [+] To lengthen
	06 Trimming Adjustment Adjust the trimming width. The trim width should be more than 2.0 mm, otherwise the trimming operation may not be performed properly.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm) Adj. Range: -400~+400 1 step = 0.1 mm [-] To narrow [+] To widen
	07 Tri-Fold Position Adj. Adjust the folded positions in Tri-Fold mode. Set Fold 1toFold 2 in sequence.	Objects of adjustment: Offset for All Size, A4 short edge feed, 8.5 11 short edge feed Fold 1, Fold 2: Adj. Range: -100~+100 1 step = 0.1 mm Fold 1: To widen [-] <-> [+] To narrow Fold 2: To narrow [-] <-> [+] To widen
	08 Trimmer Receiver Adj. Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually. *Trimmer Receiver Adj. is not displayed by default. To use this setting, please contact your service representative.	Objects of adjustment: Trim Count Adjustment range: 700 times, 500 times, 300 times Objects of adjustment: Move Pitch Adjustment range: 1.0 mm, 1.5 mm, 2.0 mm Execute Compulsive Movement

Adjustment item and description

Objects/range of adjustment

04 Saddle Stitcher Adjustment

01 Fold Paper Width Adj.

Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To reduce the misalignment [+] To reduce the distortion

02 Half-Fold Position Adj.

Adjust the fold position determined by the half-folder.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To shorten the top face [+] To lengthen the top face

03 Staple Paper Width Adj.

Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the distortion

04 Staple Center Position

Adjust the center position of staples determined by the saddle stitcher.

Prerequisite: Staple paper width adjustment is completed.

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To move closer to paper center (fold) [+] To move away from paper center (fold)

05 Staple Pitch Adjustment

Adjust the staple pitch determined by the saddle stitcher.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -20~+20 1 step = 1.0 mm

[-] To shorten [+] To lengthen

06 Trimming Adjustment

Adjust the trimming width.
The trim width should be more than 2.0 mm, otherwise the trimming operation may not be performed properly.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~463 mm), Custom(257~379 mm)

Adj. Range: -400~+400 1 step = 0.1 mm

[-] To narrow [+] To widen

07 Tri-Fold Position Adj.

Adjust the folded positions in Tri-Fold mode.

Set Fold 1toFold 2 in sequence.

Objects of adjustment:

Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Fold 1, Fold 2: Adj. Range: -100~+100 1 step = 0.1 mm

Fold 1: To widen [-] <-> [+] To narrow

Fold 2: To narrow [-] <-> [+] To widen

08 Trimmer Receiver Adj.

Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually.

*Trimmer Receiver Adj. is not displayed by default. To use this setting, please contact your service representative.

Objects of adjustment: Trim Count

Adjustment range: 700 times, 500 times, 300 times

Objects of adjustment: Move Pitch

Adjustment range: 1.0 mm, 1.5 mm, 2.0 mm

Execute Compulsive Movement

Finisher Adjustment (Saddle Stitcher SD-513)

This menu item is to be displayed and allowed on the machine mounted with Saddle Stitcher SD-513.

Adjustment item and description	Objects/range of adjustment
04 Saddle Stitcher Adjustment
	01 Fold Paper Width Adj. Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment.	Adjustment range: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, PI Paper, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -50~+50 1 step = 0.1 mm [-] To reduce the misalignment [+] To reduce the distortion
	02 Fold Skew Adjustment Adjust the skew of the folding line.	Objects of adjustment: Single Fold, Multi Fold Adjustment range: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, PI Paper, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -50~+50 1 step = 0.1 mm [-] To weaken [+] To strengthen
	03 Half-Fold Position Adj. Adjust the folded position for half-fold.	Adjustment range: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -50~+50 1 step = 0.1 mm [-] To shorten the top face [+] To lengthen the top face
	04 Tri-Fold Position Adj. Adjust the folded positions in Tri-Fold mode. Adjust Fold 1to and Fold 2 in this order.	Adjustment range: Offset for All Size, A4 short edge feed, 8.5 11 short edge feed Fold 1: Adj. Range: -100~+90 1 step = 0.1 mm [-] To widen [+] To narrow Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm [-] To widen [+] To narrow
	05 Crease Position Adjustment Adjust the crease position.
		01 Half-Fold Crease Position Move the half-fold crease position.	Adjustment range: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -20~+20 1 step = 0.1 mm [-] To shorten [+] To lengthen
		02 Tri-Fold Crease Position Move the tri-fold crease position.	Adjustment range: Offset for All Size, A4 short edge feed, 8.5 11 short edge feed Fold 1, Fold 2: Adj. Range: -20~+20 1 step = 0.1 mm [-] To shorten [+] To lengthen
		03 PB Cover Crease Position Move the perfect binding cover crease position. This menu item is to be displayed and allowed on the machine mounted with Perfect Binder PB-503.	Adjustment range: Crease Line 1, Crease Line 2: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -20~+20 1 step = 0.1 mm [-] To shorten [+] To lengthen
	06 Staple Paper Width Adj. Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode.	Objects of adjustment: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the dispersion [+] To reduce the distortion
	07 Staple Center Position Adjust the center position of staples determined by the saddle stitcher. Prerequisite: Staple paper width adjustment is completed.
		01 2 Position Staple Adjust the center position for 2-position staple.	Adj. Range: -20~+20 1 step = 0.1 mm [-] To move rearward [+] To move frontward
		02 4 Position Staple(Front 2) Adjust the center position at two locations on the front edge for 4-position staple.	Objects of adjustment: Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm) Adj. Range: -100~+100 1 step = 0.1 mm [-] To move rearward [+] To move frontward
		03 4 Position Staple(Rear 2) Adjust the center position at two locations on the rear edge for 4-position staple.	Objects of adjustment: Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm) Adj. Range: -100~+100 1 step = 0.1 mm [-] To move rearward [+] To move frontward
	08 Staple Pitch Adjustment Adjust the staple pitch determined by the saddle stitcher.
		01 2 Position Staple Adjust the pitch for 2-position staple.	Adjustment range: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -20~+20 1 step = 1.0 mm [-] To shorten [+] To lengthen
		02 4 Position Staple(Front 2) Adjust the pitch at two locations on the front edge for 4-position staple.	Adjustment range: Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm) Adj. Range: -10~+10 1 step = 1 mm [-] To shorten [+] To lengthen
		03 4 Position Staple(Rear 2) Adjust the pitch at two locations on the rear edge for 4-position staple.	Adjustment range: Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm) Adj. Range: -10~+10 1 step = 1 mm [-] To shorten [+] To lengthen
	09 Staple Offset Adjustment Adjust the misalignment between the stapling positions and folding line.	Adj. Range: -10~+10 1 step = 0.1 mm [-] To move leftward [+] To move rightward
	10 Staple Tip Adjustment Change the staple leg shape.	Adj. Range: -9~+9 1 step = 1 msec [-] To be round [+] To be flat
	11 Flattening a Fold (Strength) Adjust the spine shape while changing the strength to form the book spine.	Adj. Range: -20~+20 1 step = 0.1 mm [-] To decrease the force [+] To increase the force
	12 Flattening a Fold (Freq.) Adjust the number of roller reciprocation times to form the book spine.	Adj. Range: -5~+5 1 step = 1 [-] To decrease [+] To increase
	13 Parallel Trimming Adjustment Adjust the levelness between the trimming line and cut edge.	Adjustment range: Front, Rear Adj. Range: 0~+30 1 step = 0.1 mm [Up the numerical value] To widen [Down the numerical value] To narrow
	14 Fore-edge Trimming Adj. Adjust the trimming width. The trimming width should be more than 5 mm, otherwise the trimming operation may not performed properly.	Adjustment range: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed Adj. Range: -400~+400 1 step = 0.1 mm [-] To narrow [+] To widen
	15 2-Side Slitting Adjustment Adjust the 2-side slitting.	Adjustment range: Front, Rear Adj. Range: -10~+10 1 step = 0.1 mm [-] To narrow [+] To widen
	16 2-Side Slit Finishing Adj. Change the 2-side trimming speed to adjust skew and napping conditions.	Objects of adjustment: 61 g/m2 or Less, 62 g/m2 or More Adj. Range: -4~+4 1 step = 5 mm/sec [-] Slow (Reduct rough cut) [+] Fast (Reduce curve)
	17 Trimmer Receiver Adj. Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually. *Trimmer Receiver Adj. is not displayed by default. To use this setting, please contact your service representative.	Objects of adjustment: Trim Count Adjustment range: 700 times, 500 times, 300 times Objects of adjustment: Move Pitch Adjustment range: 1.0 mm, 1.5 mm, 2.0 mm Execute Compulsive Movement

Adjustment item and description

Objects/range of adjustment

04 Saddle Stitcher Adjustment

01 Fold Paper Width Adj.

Adjust the width of adjustment plates if half-folded or tri-folded sheets show misalignment.

Adjustment range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, PI Paper, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To reduce the misalignment [+] To reduce the distortion

02 Fold Skew Adjustment

Adjust the skew of the folding line.

Objects of adjustment: Single Fold, Multi Fold

Adjustment range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, PI Paper, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To weaken [+] To strengthen

03 Half-Fold Position Adj.

Adjust the folded position for half-fold.

Adjustment range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To shorten the top face [+] To lengthen the top face

04 Tri-Fold Position Adj.

Adjust the folded positions in Tri-Fold mode.

Adjust Fold 1to and Fold 2 in this order.

Adjustment range:

Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Fold 1: Adj. Range: -100~+90 1 step = 0.1 mm

[-] To widen [+] To narrow

Fold 2: Adj. Range: -50~+50 1 step = 0.1 mm

[-] To widen [+] To narrow

05 Crease Position Adjustment

Adjust the crease position.

01 Half-Fold Crease Position

Move the half-fold crease position.

Adjustment range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To shorten [+] To lengthen

02 Tri-Fold Crease Position

Move the tri-fold crease position.

Adjustment range:

Offset for All Size, A4 short edge feed, 8.5 11 short edge feed

Fold 1, Fold 2: Adj. Range: -20~+20 1 step = 0.1 mm

[-] To shorten [+] To lengthen

03 PB Cover Crease Position

Move the perfect binding cover crease position.

This menu item is to be displayed and allowed on the machine mounted with Perfect Binder PB-503.

Adjustment range:

Crease Line 1, Crease Line 2: Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To shorten [+] To lengthen

06 Staple Paper Width Adj.

Adjust the width of adjustment plates of the saddle stitcher to be used in Staple mode.

Objects of adjustment:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the distortion

07 Staple Center Position

Adjust the center position of staples determined by the saddle stitcher.

Prerequisite: Staple paper width adjustment is completed.

01 2 Position Staple

Adjust the center position for 2-position staple.

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To move rearward [+] To move frontward

02 4 Position Staple(Front 2)

Adjust the center position at two locations on the front edge for 4-position staple.

Objects of adjustment:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm)

Adj. Range: -100~+100 1 step = 0.1 mm

[-] To move rearward [+] To move frontward

03 4 Position Staple(Rear 2)

Adjust the center position at two locations on the rear edge for 4-position staple.

Objects of adjustment:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm)

Adj. Range: -100~+100 1 step = 0.1 mm

[-] To move rearward [+] To move frontward

08 Staple Pitch Adjustment

Adjust the staple pitch determined by the saddle stitcher.

01 2 Position Staple

Adjust the pitch for 2-position staple.

Adjustment range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -20~+20 1 step = 1.0 mm

[-] To shorten [+] To lengthen

02 4 Position Staple(Front 2)

Adjust the pitch at two locations on the front edge for 4-position staple.

Adjustment range:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm)

Adj. Range: -10~+10 1 step = 1 mm

[-] To shorten [+] To lengthen

03 4 Position Staple(Rear 2)

Adjust the pitch at two locations on the rear edge for 4-position staple.

Adjustment range:

Offset for All Size, B4 short edge feed, 8K short edge feed, 11 17 short edge feed, A3 short edge feed, Custom(380~488 mm), Custom(257~379 mm)

Adj. Range: -10~+10 1 step = 1 mm

[-] To shorten [+] To lengthen

09 Staple Offset Adjustment

Adjust the misalignment between the stapling positions and folding line.

Adj. Range: -10~+10 1 step = 0.1 mm

[-] To move leftward [+] To move rightward

10 Staple Tip Adjustment

Change the staple leg shape.

Adj. Range: -9~+9 1 step = 1 msec

[-] To be round [+] To be flat

11 Flattening a Fold (Strength)

Adjust the spine shape while changing the strength to form the book spine.

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To decrease the force [+] To increase the force

12 Flattening a Fold (Freq.)

Adjust the number of roller reciprocation times to form the book spine.

Adj. Range: -5~+5 1 step = 1

[-] To decrease [+] To increase

13 Parallel Trimming Adjustment

Adjust the levelness between the trimming line and cut edge.

Adjustment range:

Front, Rear

Adj. Range: 0~+30 1 step = 0.1 mm

[Up the numerical value] To widen

[Down the numerical value] To narrow

14 Fore-edge Trimming Adj.

Adjust the trimming width.

The trimming width should be more than 5 mm, otherwise the trimming operation may not performed properly.

Adjustment range:

Offset for All Size, SRA3 short edge feed, A3 short edge feed, B4 short edge feed, SRA4 short edge feed, A4 short edge feed, B5 short edge feed, 12 18 short edge feed, 11 17 short edge feed, 8.5 14 short edge feed, 8.5 11 short edge feed, 8 13 short edge feed, 8K short edge feed, 16K short edge feed, Custom(380~488 mm), Custom(257~379 mm), 13 19 short edge feed

Adj. Range: -400~+400 1 step = 0.1 mm

[-] To narrow [+] To widen

15 2-Side Slitting Adjustment

Adjust the 2-side slitting.

Adjustment range:

Front, Rear

Adj. Range: -10~+10 1 step = 0.1 mm

[-] To narrow [+] To widen

16 2-Side Slit Finishing Adj.

Change the 2-side trimming speed to adjust skew and napping conditions.

Objects of adjustment:

61 g/m2 or Less, 62 g/m2 or More

Adj. Range: -4~+4 1 step = 5 mm/sec

[-] Slow (Reduct rough cut) [+] Fast (Reduce curve)

17 Trimmer Receiver Adj.

Frequent trimming operations may cause damage to the receiver, resulting in trimming failures. Move the receiver automatically or manually.

*Trimmer Receiver Adj. is not displayed by default. To use this setting, please contact your service representative.

Objects of adjustment: Trim Count

Adjustment range: 700 times, 500 times, 300 times

Objects of adjustment: Move Pitch

Adjustment range: 1.0 mm, 1.5 mm, 2.0 mm

Execute Compulsive Movement

Finisher Adjustment (Perfect Binder PB-503)

This menu item is to be displayed and allowed on the machine mounted with Perfect Binder PB-503.

Adjustment item and description	Objects/range of adjustment
05 Perfect Binder Adjustment
	01 Sub Compile CD Width Adj. Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.	Objects of adjustment: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm) Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the distortion [+] To reduce the dispersion
	02 Clamp CD Width Adjustment Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.	Objects of adjustment: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm) Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the distortion [+] To reduce the dispersion
	03 Clamp FD Position Adj. Adjust misalignment or distortion in the paper feed direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.	Objects of adjustment: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm) Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the distortion [+] To reduce the dispersion
	04 Glue Start Position Adjust the position to start gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.	Objects of adjustment: Ahead, Back: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm) Adj. Range: -128~+127 1 step = 0.1 mm [-] To increase [+] To decrease
	05 Glue Finish Position Adjust the position to finish gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.	Objects of adjustment: Ahead, Back: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm) Adj. Range: -128~+127 1 step = 0.1 mm [-] To decrease [+] To increase
	06 Cover Lead Edge Adj. Adjust the position of the lead edge of the left cover sheet. The sizes referred to in this section are those of bodies corresponding to cover sizes.	Objects of adjustment: PB Tray: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm) Except PB Tray: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm) Adj. Range: -128~+127 1 step = 0.1 mm [-] To move closer to the body [+] To move further from the body
	07 Cover Trimming Adjustment Adjust the trimming width of the right cover sheet. To align the lead edges of left and right cover pages, be sure to perform Cover Lead Edge Adjustment in advance.	Objects of adjustment: Perfect Binder Tray, Except PB Tray Adj. Range: -128~+127 1 step = 0.1 mm [-] To narrow [+] To widen
	08 Cover Up/Down CD Width Adj. Adjust the misalignment between the cover sheet and body.	Objects of adjustment: Perfect Binder Tray, Except PB Tray Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the distortion [+] To reduce the misalignment
	09 Spine Corner Forming Pos. Adjust the form of cover paper.	Objects of adjustment: Up/Down Forward Adj. (Front), Up/Down Rear Adj. (Back) Adj. Range: -128~+127 1 step = 0.1 mm [-] To convex [+] To concave
	10 Temperature Adjustment Glue Tank -Low: Adjust the temperature to control the tank heater. (Temperature low) Down: viscosity increased (Temperature high) Up: viscosity decreased Glue Apply Roller: Adjust the temperature to control the roller heater. This also supports heating of the glue. (Temperature low) Down: viscosity increased (Temperature high) Up: viscosity decreased	Object of Adjustment: Glue Tank -Low Initial: 185°C Adj. Range: 180~190 1 step = 1°C Up: viscosity decreased. Down: viscosity increased. Object of Adjustment: Glue Apply Roller Initial: 165°C Adj. Range: 160~170 1 step = 1°C Up: viscosity decreased. Down: viscosity increased.

Adjustment item and description

Objects/range of adjustment

05 Perfect Binder Adjustment

01 Sub Compile CD Width Adj.

Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the distortion [+] To reduce the dispersion

02 Clamp CD Width Adjustment

Adjust misalignment or distortion in the crosswise direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the distortion [+] To reduce the dispersion

03 Clamp FD Position Adj.

Adjust misalignment or distortion in the paper feed direction of the body if detected. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the distortion [+] To reduce the dispersion

04 Glue Start Position

Adjust the position to start gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Ahead, Back: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To increase [+] To decrease

05 Glue Finish Position

Adjust the position to finish gluing on the body. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

Ahead, Back: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To decrease [+] To increase

06 Cover Lead Edge Adj.

Adjust the position of the lead edge of the left cover sheet. The sizes referred to in this section are those of bodies corresponding to cover sizes.

Objects of adjustment:

PB Tray: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Except PB Tray: Offset for All Size, A4 long edge feed, B5 long edge feed, A5 long edge feed, 8.5 11 long edge feed, 16K long edge feed, A5 short edge feed, 5.5 8.5 short edge feed, 5.5 8.5 long edge feed, Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To move closer to the body [+] To move further from the body

07 Cover Trimming Adjustment

Adjust the trimming width of the right cover sheet. To align the lead edges of left and right cover pages, be sure to perform Cover Lead Edge Adjustment in advance.

Objects of adjustment:

Perfect Binder Tray, Except PB Tray

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To narrow [+] To widen

08 Cover Up/Down CD Width Adj.

Adjust the misalignment between the cover sheet and body.

Objects of adjustment:

Perfect Binder Tray, Except PB Tray

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the distortion [+] To reduce the misalignment

09 Spine Corner Forming Pos.

Adjust the form of cover paper.

Objects of adjustment:

Up/Down Forward Adj. (Front), Up/Down Rear Adj. (Back)

Adj. Range: -128~+127 1 step = 0.1 mm

[-] To convex [+] To concave

10 Temperature Adjustment

Glue Tank -Low:

Adjust the temperature to control the tank heater.

(Temperature low) Down: viscosity increased

(Temperature high) Up: viscosity decreased

Glue Apply Roller:

Adjust the temperature to control the roller heater. This also supports heating of the glue.

(Temperature low) Down: viscosity increased

(Temperature high) Up: viscosity decreased

Object of Adjustment: Glue Tank -Low

Initial: 185°C

Adj. Range: 180~190 1 step = 1°C

Up: viscosity decreased. Down: viscosity increased.

Object of Adjustment: Glue Apply Roller

Initial: 165°C

Adj. Range: 160~170 1 step = 1°C

Up: viscosity decreased. Down: viscosity increased.

Finisher Adjustment (Relay Unit RU-510)

This menu item is to be displayed and allowed on the machine mounted with Relay Unit RU-510.

Adjustment item and description	Objects/range of adjustment
06: Relay Stacker (RU) Adjustment
	01 Paper Width Adjustment Adjust the alignment plate position in the crosswise direction of Relay Unit RU-510. Perform this adjustment when paper distortion or skew is detected in the finisher following Relay Unit RU-510. For example, adjust a misalignment of punch holes in the crosswise direction.	Objects of adjustment: Offset for All Size, 11 17 short edge feed, A3 short edge feed, B4 short edge feed, 8.5 14 short edge feed, A4 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, A4 long edge feed, B5 long edge feed, A5 long edge feed, 5.5 8.5 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 12 18 short edge feed, SRA3 short edge feed, SRA4 short edge feed, 9 11 long edge feed, Postcard, Custom(220~379 mm), Custom(100~219 mm) Adj. Range: -20~+20 1 step = 0.1 mm [-] To reduce the randomness [+] To reduce the tilts
	02 Paper Length Adjustment Adjust the alignment plate position in the paper feed direction of Relay Unit RU-510. Perform this adjustment when paper distortion or skew is detected in the finisher following Relay Unit RU-510. For example, adjust a misalignment of punch holes in the paper feed direction.	Objects of adjustment: Offset for All Size, 11 17 short edge feed, A3 short edge feed, B4 short edge feed, 8.5 14 short edge feed, A4 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, A4 long edge feed, B5 long edge feed, A5 long edge feed, 5.5 8.5 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 12 18 short edge feed, SRA3 short edge feed, SRA4 short edge feed, 9 11 long edge feed, Postcard, Custom(380~488 mm), Custom(220~379 mm), Custom(148~219 mm) Adj. Range: -50~+50 1 step = 0.1 mm [-] To reduce the dispersion [+] To reduce the tilts

Adjustment item and description

Objects/range of adjustment

06: Relay Stacker (RU) Adjustment

01 Paper Width Adjustment

Adjust the alignment plate position in the crosswise direction of Relay Unit RU-510. Perform this adjustment when paper distortion or skew is detected in the finisher following Relay Unit RU-510.

For example, adjust a misalignment of punch holes in the crosswise direction.

Objects of adjustment:

Offset for All Size, 11 17 short edge feed, A3 short edge feed, B4 short edge feed, 8.5 14 short edge feed, A4 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, A4 long edge feed, B5 long edge feed, A5 long edge feed, 5.5 8.5 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 12 18 short edge feed, SRA3 short edge feed, SRA4 short edge feed, 9 11 long edge feed, Postcard, Custom(220~379 mm), Custom(100~219 mm)

Adj. Range: -20~+20 1 step = 0.1 mm

[-] To reduce the randomness [+] To reduce the tilts

02 Paper Length Adjustment

Adjust the alignment plate position in the paper feed direction of Relay Unit RU-510. Perform this adjustment when paper distortion or skew is detected in the finisher following Relay Unit RU-510.
For example, adjust a misalignment of punch holes in the paper feed direction.

Objects of adjustment:

Offset for All Size, 11 17 short edge feed, A3 short edge feed, B4 short edge feed, 8.5 14 short edge feed, A4 short edge feed, 8.5 11 short edge feed, 8.5 11 long edge feed, A4 long edge feed, B5 long edge feed, A5 long edge feed, 5.5 8.5 long edge feed, 8 13 short edge feed, 8K short edge feed, 16K long edge feed, 16K short edge feed, 12 18 short edge feed, SRA3 short edge feed, SRA4 short edge feed, 9 11 long edge feed, Postcard, Custom(380~488 mm), Custom(220~379 mm), Custom(148~219 mm)

Adj. Range: -50~+50 1 step = 0.1 mm

[-] To reduce the dispersion [+] To reduce the tilts

ADF Adjustment

Adjustment item and description	Objects/range of adjustment
01 ADF Original Stop Pos. Adj. Adjust the position to start scanning on the ADF and the image position in the crosswise direction. Prerequisite: FD-Mag. Adjustment should be completed before adjusting the position to start scanning. Printer Centering Adjustment should be completed before adjusting the image position.	Objects of adjustment: Restart Timing (Front), Restart Timing (Back) Adj. Range: -40~+40 1 step = 0.1 mm [-] Image Fast [+] Image Slow Objects of adjustment: Centering (Front), Centering (Back) Adj. Range: -44~+44 1 step = 0.1 mm [-] Front [+] Back
02 ADF Orig. Stop Pos. Auto Automatically adjust the position to start scanning on the ADF and the image position in crosswise direction. Prerequisite: FD-Mag. Adjustment should be completed before adjusting the position to start scanning. Printer Centering Adjustment should be completed before adjusting the image position.	Objects of adjustment: Restart Timing (Front), Restart Timing (Back) Centering (Front), Centering (Back)
03 FD-Mag. Adjustment Adjust the magnification in paper feed direction when scanning on the ADF. Prerequisite: Printer FD-Mag. Adjustment is completed.	Objects of adjustment: ADF Adj. Range: -20~+20 1 step = 0.1 % [-] Short [+] Long
04 FD-Mag. Auto Adjustment Automatically adjust the magnification in paper feed direction when scanning on the ADF.	Objects of adjustment: ADF
05 Home Read Position Adj(Back) Adjust the home position of the shading shaft to correct any image failure due to dirt on the shading shaft on the back side of the ADF.	Adj. Range: -4~+4 1 step = 1
06 FD-Mag. Adjustment(Back) Adjust the magnification in paper feed direction on the back side when scanning on the ADF. Prerequisite: Printer FD-Mag. Adjustment is completed.	Objects of adjustment: ADF Adj. Range: -20~+20 1 step = 0.1 % [-] Short [+] Long
07 FD-Mag. Auto Adj.(Back) Automatically adjust the magnification in paper feed direction on the back side when scanning on the ADF.	Objects of adjustment: ADF
08 Main Scan Dir. Zoom(Back) Adjust the magnification in crosswise direction on the back side when scanning on the ADF. Prerequisite: Printer CD-Mag. Adjustment is completed.	Objects of adjustment: ADF Adj. Range: -10~+10 1 step = 0.1 % [-] Short [+] Long
09 Main ScanDir.Zoom Auto(Back) Automatically adjust the magnification in crosswise direction on the back side when scanning on the ADF.	Objects of adjustment: ADF
10 Original Tray Pre-rise Set. Adjust the standby position of the Original feed tray on the ADF.	Original Tray Pre-rise: ON, OFF Objects of adjustment: Paper Tray Adjustment range: (1-7)

Adjustment item and description

Objects/range of adjustment

01 ADF Original Stop Pos. Adj.

Adjust the position to start scanning on the ADF and the image position in the crosswise direction.

Prerequisite: FD-Mag. Adjustment should be completed before adjusting the position to start scanning. Printer Centering Adjustment should be completed before adjusting the image position.

Objects of adjustment:

Restart Timing (Front), Restart Timing (Back)

Adj. Range: -40~+40 1 step = 0.1 mm

[-] Image Fast [+] Image Slow

Objects of adjustment:

Centering (Front), Centering (Back)

Adj. Range: -44~+44 1 step = 0.1 mm

[-] Front [+] Back

02 ADF Orig. Stop Pos. Auto

Automatically adjust the position to start scanning on the ADF and the image position in crosswise direction.

Prerequisite: FD-Mag. Adjustment should be completed before adjusting the position to start scanning. Printer Centering Adjustment should be completed before adjusting the image position.

Objects of adjustment:

Restart Timing (Front), Restart Timing (Back)
Centering (Front), Centering (Back)

03 FD-Mag. Adjustment

Adjust the magnification in paper feed direction when scanning on the ADF.

Prerequisite: Printer FD-Mag. Adjustment is completed.

Objects of adjustment:

ADF

Adj. Range: -20~+20 1 step = 0.1 %

[-] Short [+] Long

04 FD-Mag. Auto Adjustment

Automatically adjust the magnification in paper feed direction when scanning on the ADF.

Objects of adjustment:

ADF

05 Home Read Position Adj(Back)

Adjust the home position of the shading shaft to correct any image failure due to dirt on the shading shaft on the back side of the ADF.

Adj. Range: -4~+4 1 step = 1

06 FD-Mag. Adjustment(Back)

Adjust the magnification in paper feed direction on the back side when scanning on the ADF.

Prerequisite: Printer FD-Mag. Adjustment is completed.

Objects of adjustment:

ADF

Adj. Range: -20~+20 1 step = 0.1 %

[-] Short [+] Long

07 FD-Mag. Auto Adj.(Back)

Automatically adjust the magnification in paper feed direction on the back side when scanning on the ADF.

Objects of adjustment:

ADF

08 Main Scan Dir. Zoom(Back)

Adjust the magnification in crosswise direction on the back side when scanning on the ADF.

Prerequisite: Printer CD-Mag. Adjustment is completed.

Objects of adjustment:

ADF

Adj. Range: -10~+10 1 step = 0.1 %

[-] Short [+] Long

09 Main ScanDir.Zoom Auto(Back)

Automatically adjust the magnification in crosswise direction on the back side when scanning on the ADF.

Objects of adjustment:

ADF

10 Original Tray Pre-rise Set.

Adjust the standby position of the Original feed tray on the ADF.

Original Tray Pre-rise: ON, OFF

Objects of adjustment: Paper Tray

Adjustment range: (1-7)

Size Memory Recovery Mode

Adjustment item and description			Objects/range of adjustment
Perform drum pre-rotation for 1 minute.			Start

Charge Manual Cleaning

Adjustment item and description			Objects/range of adjustment
Perform charging corona cleaning.			Start

Drum Memory Recovery Mode

Adjustment item and description			Objects/range of adjustment
Perform drum pre-rotation for 3 minutes.			Start

Drum Refresh Mode

Adjustment item and description			Objects/range of adjustment
Rotate drum to refresh surface.			Start

Gamma Automatic Adjustment

Adjustment item and description			Objects/range of adjustment
Perform gamma automatic adjustment.			Start

Toner Refresh Manual Adj.

Adjustment item and description			Objects/range of adjustment
Perform the manual toner refresh.			Start

CL Blade Cleaning Mode

Adjustment item and description			Objects/range of adjustment
Perform CL blade cleaning for approximately 3 minutes.			Start